I ask because I haven't had to deal with reprogramming vagcom. I have a TL886II plus programmer, arduino, USB ASP, I can do something with them?
i dont know the vagcom is possibly to reinstall without detach the microcontroller? I have something programmers but as I said I programmed on the microcontrollers themselves, with thw microcontroller down, on the pins. If anyone can help me with advice and dumps for reinstall the software on vagcom i would be greateful. the error with usb library, i think i need to reinstal the software,or if anyone knows if can do something else.įirst vagcom is V12.12 the other vagcom is 189.īefore I start reinstalling the software, I thought in the forum I asked what and how it is done, i worked with microcontrollers but with microcontroller itself. I am 2 vagcoms but both vagcoms are the same problem. talking with no real help, to bad.for them. I try to solve things with obd2cartool client support but, at first they said they not sell HW 44 (see pics from they site), after a while they admit to sell it, but keep. I used same dumps/loader/18.9.0 with an identical cable and worked ok, it is not about the reflash. I tried on pc with win7 and 10, with Audi A4, Golf mk6, Caddy, same behaviour with all. I tried to make it worked using usbasp with dumps from 18.2 to 18.9.0, using loader v.7 to v7.2 but no luck, after I connect cable to car works about 20 seconds and program freezes and it is necessary to disconect usb cable in order to connect again. I wanna share with you an issue with a cable from obd2cartool. There’s a label on the interface where shows “ vcds 171 vag hex+can “Įnviado desde mi iPhone utilizando Tapatalk I installed the vcds 17.1.3 est from your link and the program doesn’t open. Hello, first I wanna give thanks for answer. Also, read the topic about updating the cable to the latest version. If it works, let it send you a link to the software and loader.
If you only bought English then ask the seller if the cable will work with the Spanish version.
What cable version and where did you buy it? You should buy the English (18.2.0) and Spanish (17.8.1) versions. When programming, keep in mind correct order:įorum VCDS-Release-11.11.0-Installer can not extract, who can use the VCDS-Release-11.11.0-Installer Thank you
#Vcds 12.12.0 cracked rar#
Remove rar extension from filepart of VCDS software. Use VCDS 11.11.0 loader if you have a RL interface. Here you can find dump (Atmega flash+eeprom)
Hex files are for pony prog, bin files for upa. If VCDS loader finds the protection chip, it then unlocks communication with ATMega, creates d1-d3 files and starts VCDS. It communicates with VCDS loader through RTS/CTS pins of FTDI.
#Vcds 12.12.0 cracked cracked#
CN Clone dump is not the same as HCC196.bin.Īs I know - protection chip doesn't protect ATMega (according to schematic I don't know how it can protect it) but is used as a "key" for cracked VCDS distributed with VAG-COM. HP196.bin is for new HW type (0x46) - not decryptable yet (no public). HCC196.bin is for old HW type (0x44) with PORTA.2 and PORTA.3 connected to GAL I'm working on other tools such as FLASH and EEPROM dumper via USB, so it can be read even with fuse bits set.īTW according to FW source code - fuse bits are not read by firmware itself, so it doesn't care if the fuse bits are set or not.
#Vcds 12.12.0 cracked install#
It's quite easy to decrypt HCC196.bin (old 512 byte bootlader) from install directory. Here are flash dumps for latest VAG-COM original + flash dump of China clone FW 1.96 with protection chip.